PoE Extender (Waterproof, 2-way output) LAN-EXPOE3

[An industrial PoE extender that supports PoE reception of the IEEE802.3bt standard (maximum 90W) and can extend up to 100m by splitting a LAN cable into two. Also compliant with the IP67 waterproof standard.]

●This PoE extender supports PoE reception of IEEE802.3bt (90W)/at (30W)/af (15.4W) and can extend up to 100m while supplying power and communication to two PoE devices (IEEE802.3at/af).
*1, *2, *3, *4, *5, *6, *7, *8
●By receiving PoE reception of IEEE802.3bt (90W), this product can be split into two to supply PoE power of IEEE802.3at (30W) and af (15.4W). *4, *5
●This industrial PoE extender complies with the IP67 waterproof standard, enabling the transmission and extension of PoE signals outdoors.
●It operates in a wide range of environments with an operating temperature range of -20 to 60 degrees Celsius.
●Since the main unit operates on PoE power, no power cable is required when relaying/extending.
●By relaying up to two of these products, the LAN cable can be extended up to approximately 300m.
Furthermore, by distributing the distributed LAN signal, it is possible to supply power and communication to multiple PoE devices. *2, *3, *4, *5, *6, *7, *8
●Equipped with an LED that can be used to check the communication and power supply status.

*1 This is a theoretical value based on the LAN cable standard.
*2 Due to power loss on the LAN cable and power consumption by the product itself, the PoE power supplied when passing through this product will decrease.
*3 The maximum number of devices that can be extended may differ because the power supplied differs depending on the standard of the PoE supply device and the cable length.
*4 The PoE supply device must be compatible with IEEE802.3af/at/bt, and the PoE device receiving power must be compatible with IEEE802.3at/af.
*5 If the PoE supply device is IEEE802.3af, PoE power output from this product will not be supported. (Power will be supplied, but the voltage and power output will not conform to the PoE standard.)
*6 For PoE power supply, please use a Category 5e/6/6a straight cable with a thickness of 24AWG or more.
Waterproof performance may not be achieved when using a LAN cable with a thickness of less than 24AWG.
*7 Please use a LAN cable with a LAN connector diameter of 13mm or less. If the LAN connector is 13mm or larger, it cannot pass through the waterproof cap.
*8 If the LAN connector has a latch cover, please cut off the latch cover before use.
Recommended cables (Sanwa Supply)
・KB-T6POE series (22AWG)
・KB-T6TS series (23AWG)
・KB-T5T series (24AWG), etc.
*9 This product's PoE OUT only supports IEEE802.3af/at. Therefore, it will not work even if you connect an IEEE802.3bt PoE device.
*10 The waterproof function is only enabled when LAN cables are connected to all of this product's PoE input/output ports. Please note that it will not be waterproof when LAN cables are not connected.


■Color: Silver
■Size: W150×D72.94×H43.8mm
■Weight: Approx. 372g
■Number of ports: 2 ports
■Maximum transmission speed: 1000Mbps (1000BASE-T)
■Standards: IEEE802.3 (10BASE-T)
IEEE802.3u (100BASE-TX)
IEEE802.3ab (1000BASE-T)
IEEE802.3x (Flow control for Full-Duplex)
【PoE receiving port】IEEE802.3af/at/bt (90W)
【PoE supplying port】IEEE802.3af/at (30W)
*The power that can be supplied will decrease relative to the input power due to the power consumption of this product itself and the power reduction effect on the LAN cable. Therefore, although it falls slightly below the IEEE 802.3af/at standard, it is compatible with the device.
■Access Method: CSMA/CD
■Switching Method: Store & Forward
■Communication Mode: Full Duplex/Half Duplex
■Port Configuration: [Input] IEEE802.3af/at/bt, 1000BASE-T/100BASE-TX/10BASE-T (RJ-45) AUTO-MDIX ×1 port
[Output] IEEE802.3af/at, 1000BASE-T/100BASE-TX/10BASE-T (RJ-45) AUTO-MDIX ×2 ports
■PoE Support: Supported
■PoE Port Output: af standard 15.4W/1 port (maximum), at standard 30W/1 port (maximum)
■PoE Power Supply Method: Alternative A
■Power Consumption (Maximum): 0.7W
■Environmental Conditions: Operating Temperature -20 to 60 degrees, Humidity 5 to 90% (non-condensing)
Storage: Temperature -40 to 80 degrees Celsius, humidity 10 to 90% (non-condensing)
■Compatible LAN cable: UTP Category 5e/6/6a straight cable with a thickness of 24AWG or more
*Please use a PoE-compatible LAN cable.
■Buffer Memory: 128Kbytes (dynamically allocated to each port)
■Flow Control: Yes
■Switch Fabric: 6Gbps
■Maximum Packet Forwarding Capacity: 4.46Mbps
■Filtering Speed: 1,488,000 packets/sec (1,000Mbps), 148,800 packets/sec (100Mbps), 14,880 packets/sec (10Mbps)
■MAC Address Table: 2K
■Jumbo Frames: Supported
■Auto MDI/MDI-X: Supported
■Auto Negotiation: Supported
■Wall Mountable: Yes
■Waterproof Rating: IP67
■ESD Protection: 6000VDC (Supports Ethernet ESD protection)
■Set Contents: Main unit x 1, Instruction manual (warranty) x 1, Clamp nuts x 3, Sealing rings x 3, Sealing covers x 3, Wall mounting screws x 4, Anchors x 4, Ground wire x 1, Spanner x 1